Gold Rat Metal Detectors is located 6/50 Freda Street Upper Mount Gravatt. This is the only store to stock Metal Detectors. Gold Rat Engineering is located 4/16 Redcliffe Gardens Drive Clontarf This is where you will see the largest range of your highbankers, sluices and accessories

News — minelab gpz7000

Blog Menu

WHERE can I go detecting gold in Queensland ?

WHERE  can  I  go  detecting  gold  in  Queensland ?

 

WHERE  CAN  I  GO  DETECTING  GOLD  IN  QUEENSLAND  ?

Now that’s a great question ! …. that we often get asked by customers/visitors to our store.

To lawfully go detecting gold nuggets (and gold specimens) in Queensland you requireQueensland ‘Fossicking Licence’.

You can purchase your Qld Fossicking Licence online using a credit card payment. Costs vary from about $10 for 1 month, up to about $60 for 1 year for an individual fossicker (A one-year Fossicking Licence for a family costs about $80). Your licence is e-mailed to you once payment is confirmed.

Fossicking Laws/Responsibilities

The Queensland Fossicking Act 1994 and it’s associated Regulations contain requirements for fossickers to maintain safety, hygiene and a high standard of behaviour. Infringement notices (on-the-spot fines) and prosecutions may be used to enforce the provisions of the legislation. Breaches may also result in cancellation of licences.

When fossicking in Queensland, some of the general responsibilities include that a person MUST NOT:
•    destroy or injure any trees
•    clear any vegetation except above an actual excavation
•    pollute any watercourse, dam or the like
•    create areas likely to erode
•    interfere with any livestock, wildlife or property infrastructure (e.g. windmills, bores, pumps, tanks, fences)
•    interfere with any heritage or cultural site
•    undermine any banks or dig pits to create any tunnels or overhanging sections.

There are also other requirements a person must follow when fossicking near watercourses, and also upon designated fossicking lands and areas.

When fossicking upon private property in Queensland, a person should also have written permission from the land owner/s.

A Qld Fossicking Licence allows you to search for, and collect fossicking materials using hand tools and for recreational, tourist and educational purposes only.
“Hand tools such as picks, shovels, hammers, sieves, shakers, electronic detectors (metal detectors) and other similar tools can be used.

No machinery is permitted. This includes water sluices with electronic pumps and dredges of any kind.

You can collect from the surface or by digging, but you are not permitted to dig below 2m of the natural ground surface of land or below 0.5m in streams. Overhangs and tunnels are not allowed.”

Also - “You can collect gemstones, ornamental stones, mineral specimens, alluvial gold (including nuggets) and some fossil specimens, but not meteorites and fossils of vertebrate animals. (The finding/ownership of meteorites in Australia will be considered in a future BLOG article).

You don’t need a fossicking licence to search for ‘treasure’ such as lost jewellery and coins on a beach.”

In other words – you can go detecting on public beaches in Queensland in search of coins and jewellery (including those made from gold or platinum or silver) without holding a Qld Fossicking Licence.

However, if you find any item of value, including jewellery – that does not belong to you - then you are required by law to hand such property in to the police. Accordingly, you are entitled to receive an official receipt from the police for the found property you hand in to them. If the police can not locate the lawful owner of that found property within a few months, then you can lawfully lodge a claim to the police for that property you found. Otherwise, if you keep valuable property that you find - that does not belong to you – you may be liable to prosecution for “Stealing by Finding”.

The Qld Police Service website contains  a List of Found Property  (including items of jewellery) reported during the past month. This information may also be useful to someone who has lost an item and not reported it to police.

 

General Permission Areas (GPA's) for Fossicking in Qld
It was recently publicly reported that:  "Queensland currently has 11 fossicking areas, 9 designated fossicking lands, and 21 General Permission Areas (GPA's) for fossicking - totaling more than 20,000 hectares"

There are 11 separate General Permission Areas (GPA's) in the Clermont area where landholders have given general permission for fossicking. Seven of these are in the Clermont State Forest. More than 11,000 Hectares (> 110 square kilometres) of General Permission Areas (GPA's) are available for fossicking near Clermont (about 950km NNW of Brisbane).

A total of about 50 square kilometres of General Permission Areas (GPA's) are available for fossicking at Durikai State Forest, about 30km west of Warwick (about 200km SW of Brisbane).

Also near Warwick (about 30km NW), approximately 5 square kilometres of General Permission Areas (GPA's) are available for fossicking at Talgai State Forest.

We regularly receive feedback (including photos) from customers, and other detectorists/prospectors, about gold nuggets being detected in the above GPA's - mostly found using Minelab Pulse-Induction (PI) technology detectors (e.g. GPZ 7000, GPX 6000, GPX 5000/4500, and SDC 2300).

 

New GPA's Sought

In late 2022 it was reported that "the Rockhampton Regional Council said it had written to the Department of Resources to try to create GPA's in three locations in Mount Morgan."

Like the 'Amalgamated Prospectors & Leaseholders Association' (APLA) of Western Australia, and also the 'Prospectors and Miners Association of Victoria' (PMAV) - perhaps what is required in Queensland is a similar membership-based body created to protect the rights and opportunities of those who wish to fossick and prospect in Queensland. Furthermore, such an Association could lobby the Queensland Government on behalf of it's members to create more opportunities for fossicking & prospecting throughout Queensland, including far more General Permission Areas.

In other States like Western Australia and Victoria there is far more total areas of ground available for fossicking and prospecting with a Miners Right - than there is currently available via GPA's in Queensland.

 

Perhaps the following online information with respect to fossicking areas in Queensland, and Qld Prospecting Permits, may also be of interest to you:

 

Queensland 'Globe'
Queensland Globe is a free online interactive website tool that you can use to identify property names (and their boundaries) including pastoral properties.
e.g. you can select following options:  All Layers > Location > Property Names


Queensland ‘GeoResGlobe’
Queensland ‘GeoResGlobe’ is another free online interactive website tool that you can use to obtain information on Queensland's mining and exploration data, including:
1.    Identify property names (and their boundaries) including pastoral properties; and
2.    Identify ‘Exploration Permits - Minerals’ (EPM’s) – either “Granted” (current) or “Application” (pending assessment); and

3. Identify 'Mining Leases' (ML's) -

covering areas/properties of interest to you. Additional available information includes the “Authorised Holder Name” of the EPM’s / ML's, as well as the “Grant Date” and “Expiry Date’ of them.


 
Upon accessing this interactive website tool, you can use the menu system on the left hand side.
Click on “Layers” > “Add Layers” > “All Layers”
Then you can choose from a list of different Layers, and also the sub-layers within each Layer (e.g. “Cadastre” > “Properties”).

Example 1 of available information - a simple search via the Qld ‘GeoResGlobe’ database revealed that:  in early May 2023 an Application was lodged for a Minerals Exploration Permit (EPM 28787) covering 230 square kilometres to the west & north-west of Durikai State Forest. Interestingly, in April & May 2023 the same Applicant also lodged EPM Applications for other areas within and around Durikai State Forest.

 

Example 2 of available information - a simple search via the Qld ‘GeoResGlobe’ database - using the menu system on the left hand side, by Clicking on “Production permits” > “Mining lease” > “ML granted”, and then selecting the letter "i" Information tool and then clicking this tool within the marked area of ML 1870 on the map, provides further information at the bottom of the screen - which revealed that within the Blair Athol State Forest, Mining Lease ML 1870 (re: "Au" - gold) was granted in 1980 and is current until June 2026, including the name of the leaseholder.



Contacting Exploration Permit Holders/Mining Companies
During my recent several years of full-time prospecting, I contacted several gold exploration and mining companies, and after voluntarily submitting written details (via e-mail) about my prospecting experience, vehicle/s, prospecting techniques & gear (including safety equipment), my Prospecting Licence/Miner's Right, and public liability insurance etc., and my intentions – I was very fortunate to be granted written conditional permission to prospect on their leases. As a result, I provided details (photos & GPS co-ordinates) of all my finds of gold nuggets to the leaseholders, who then permitted me to explore additional ground held via their leases.


Properties Allowing Prospecting & Camping
There are several properties (including large stations) throughout Queensland that permit recreational prospecting/camping for a fee. These include locations near: Georgetown/Forsythe in North Qld, and Warwick ('Glendon Camping Ground' – which is beside Durikai State Forest) in South-East Qld, and Clermont & Mount Morgan in Central Qld, and Palmerville Station in Cape York Peninsula, etc

https://www.facebook.com/flatcreekstation/

https://www.facebook.com/people/Western-Creek-Gold/100066532061530/

https://www.gilbertongold.com/

https://glendoncamping.com.au/

https://www.facebook.com/people/Fig-Tree-Camp/100066735554908/

https://goldenprospectingtours.com.au

https://mountmorganoutdoors.com.au/product/car-lyn-fossicking-off-grid-camping-property-mount-morgan/

https://www.facebook.com/people/Palmerville-Gold/100065218831323/ 

 

The website 'Hipcamp' also features several properties that permit camping & fossicking in Queensland, including in southern Qld.

To lawfully go detecting gold nuggets (and gold specimens) on such properties - a Qld Fossicking Licence is also required.

 

Unallocated State Land

The Qld Government webpage for "Fossicking Rules and Responsibilities" states: "If the land is "Unallocated State Land", you don't need permission to fossick unless:

  • there has been a native title determination over the land, or
  • the land has been ‘vested’ in another agency and used for a particular purpose."

"Unallocated state land (USL) refers to land above and below the high-water mark (HWM) that is not freehold land or land contracted to be granted in fee simple by the state; is not a road or reserve; and is not subject to a lease, licence or permit issued by the state."

The Qld Dept of Natural Resources & Mines previously reported that:

"There is a sometimes a misapprehension that there is a lot of unallocated state land or vacant crown land across the state. While there are a large number of parcels of unallocated state land, most are small in size and in odd locations. Other than a few occasional large parcels of land, the majority of land across Queensland is allocated either as freehold, leasehold, road, reserve or other tenure such as national park or state forest. Unallocated state land makes up less than 1% of Queensland land."

In June 2023 it was reported that there were "over 16,000 Unallocated State Land parcels" in Queensland.

The Qld Govt. Department of Resources (Lands Services) have recently advised that:  "As there is no list or register of available Unallocated State Land (USL) in Queensland - it is recommended that the departments FREE interactive online mapping service, Queensland Globe is accessed to allow you to search an area of interest and view all parcels of land with a tenure type of USL or SL in Queensland. This can be sourced in layers under "Planning Cadastre", by ticking "Land parcel tenure".

 
Brisbane Metal Detecting Club (BMDC)
The following information is published on the BMDC website:
“The Brisbane Metal Detecting Club (BMDC) is a non-profit organisation for metal detecting enthusiasts in Brisbane and surrounding areas. The club supports detectorists who specialise in the search for coins, jewellery and relics, as well as the infamous Australian gold nugget.
Together, the members have many years of experience in varying conditions in Australia and overseas, and are eager to share their knowledge and experience about detectors and detecting with anyone. BMDC members have access to the club's collection of helpful and educational library materials, including books, videos, maps, magazines, CDs and DVDs. Organised group trips to national goldfields and local areas of general detecting interest occur on a regular basis.

 

Books, Atlases, Online, etc.  
'Gold Prospecting’ by Doug Stone – reprinted in 2022, (192 pages) contains a section (26 pages) on goldfields in Queensland, including locations and old maps. Doug Stone has been writing prospecting books for decades, and has also authored a great range of 'Gold Atlas's' for several Australian states, including excellent maps.

    

 

A Prospectors guide to metal detecting in Australia - Gold & Ghosts’ - 2 Volumes for Qld (Volume 3 & Volume 4) by Mr. D.W. de Havelland (There are also 2 other volumes for Western Australia). These excellent/detailed books (containing numerous maps) have been out-of-print for decades, and are highly sought after.


     

Historical maps of various goldfields throughout Queensland - can be viewed online via the TROVE website. This excellent website also contains digitized historical newspapers - including reports on gold discoveries, prospecting & mining throughout Australia since the mid-1800's.

The archived website of the former Brisbane-based business of 'Treasure Enterprises of Australia' contained some excellent information on the locations and details of gold occurrences in Queensland.

The free  online database  Mindat.org  contains detailed information on minerals and their localities, deposits, and mines worldwide, including gold in Queensland.  Mindat.org has been collecting, and sharing such mineral information for the past two decades.

 

Queensland Gold Mining Leases  - Historical records held at the Qld State Archives commencing from 1871. This includes bound volumes of gold leases, including names of leaseholders and areas of leases. "Each lease in a volume includes the date of lease, name of the applicant, period of the lease and amount of rent, as well as a sketch and description of the area of the lease, and any transfers of the lease." Digital copies can also be requested.

'The Goldfields of Queensland - Charters Towers Goldfield' - a historical report published in 1899 (which has been digitized, and can be viewed online via the TROVE website) contains detailed information about the numerous gold mines that were operating around Charters Towers over 124 years ago, including old photographic images, and also details of the extent of workings and gold production results.

The 'Outdoors Queensland' website also contains some tips & resources for fossicking in Queensland.

The online ‘Prospecting Australia’ Forum contains valuable information, and has many helpful/experienced members.

Based on my experiences with hunting gold throughout the mainland of Australia - the importance of doing extensive research on likely areas of potential for finding gold can not be under-stated. Sometimes the best areas to find gold are the hardest to get to, often away from any vehicular tracks, sometimes in/nearby rugged, undulating/hilly terrain. Besides using a modern pulse-induction Minelab detector - preparation, patience & perseverance are all a must-have to find gold.

Are you up for a challenge ?

 

Large Nugget Detected in North Queensland

It was reported in 2017 that a prospector,  using a Minelab Pulse-Induction (PI) detector,  found a  1.17kg  (37.7 Ounce)  gold nugget in a field near Charters Towers. The nugget was 15cm (6 inches) below the ground. The prospector stated:

“It was beneath some vegetation so it was a bit of a challenge to get to, but now I’m thinking maybe those roots are keeping some other big nuggets safe ready to be found another time.”

 

 

Minelab GPZ 7000 - a Deep Gold Getter

Minelab GPZ 7000 - a Deep Gold Getter

 Minelab GPZ 7000 - a Deep Gold Getter

The Minelab GPZ 7000 detector was released about 8 years ago in 2015. Costing nearly ten grand, this Minelab detector is suited for serious/deep gold hunting. Experienced users often refer to the GPZ 7000 detector as the "7"or "7,000" or "Zed".

Unique ZVT Technology
The GPZ 7000 is a unique detector as it features Minelab-Patented ‘Zero Voltage Transmission’ (ZVT) technology – which, technically, is different to both Pulse Induction (PI) technology and Very Low Frequency (VLF) technologies. The inventor of the patented Minelab ZVT technology, Dr Bruce Halcro Candy, explained the differences between VLF, and PI, and ZVT technologies as follows:

“Very Low Frequency (VLF) – VLF sinewave detectors have a major disadvantage in having to ground balance out, all of the soil signals simultaneously (all three soil components above).
Pulse Induction (PI) – PI metal detectors have a major advantage of not even detecting the major soil signal; the X component, but only the saline components, but this is mostly insignificant, and the VRM component, which is just a very small percentage of the X component.
This makes the capability of PI technology to ground balance far more accurate than VLF detectors.
A disadvantage of PI is its lesser ability to detect very small nuggets compared to VLF detectors.

Another disadvantage of PI is its capability at detecting very large nuggets compared to CW metal detectors, such as ZVT. CW means Continuous Wave and includes all technologies that do not have zero transmit periods (almost all technologies other than PI).

Zero Voltage Transmission (ZVT) – ZVT has the same major advantage as PI for ground balancing in not detecting the major soil component X, but has the same advantage of CW metal detector technologies compared to PI for detecting very large nuggets because ZVT is CW (unlike PI that is not CW), and also the same advantage as PI for being relatively insensitive to saline soils compared to VLF.”

So, in simple terms - you get the best of both worlds - ZVT technology has the same excellent ground balancing properties of Pulse Induction (PI) technology while retaining Continuous Wave (i.e VLF) technology's ability to detect very small nuggets - so you can find more gold of all sizes, including deeper, even in highly mineralised soils.

Advantages of the GPZ 7000 Super-D coils - compared to Monoloop coils for PI detectors
Conventional configuration Monoloop (“Mono”) coils, and Double D coils, would both not operate effectively with ZVT technology. Hence, Minelab invented the ‘Super-D’ configuration coils (sometimes referred to as a “DOD” configuration coil).

The Minelab Super-D coils consists of two symmetric D shaped receive windings (one on the left and one on the right), with a central, oval-shaped transmit winding. This Super D coils winding geometry provides a double audio response for shallow targets, and a single audio response for deeper targets.

The Minelab Super-D coils have also been designed to have minimal response to the impacts of scraping and knocks to the coil housing - which can cause annoying false signals during detecting e.g. some PI detector coils suffer from this.
The Minelab GPZ14 Super-D coil (which is actually 14’x13’ in size), and the bigger GPZ19 Super-D coil (actually 19’x18’ in size, and weighs 1.83kg), are also both waterproof to a rated depth of 1 metre. The GPZ 7000 detector control box & control panel are NOT rated as waterproof.

Other Features of the GPZ 7000
Unlike the GPX 5000 and GPX 6000 (and most other Minelab detectors), the GPZ 7000 features a concealed coil cable whereby the coil cable (and plug) is housed (internally routed) within the removable lower shaft.

Unlike the GPX 6000, the GPZ 7000 does not have a built-in speaker. However, the GPZ 7000 is supplied with a wireless ‘Audio Module’ speaker (WM12).

With 256 Noise Cancel channels, the GPZ 7000 has enhanced immunity against Electromagnetic Interference (EMI), and hence picks up less atmospheric noise, including from power lines, electrical equipment, and also other metal detectors operating nearby. There are two options to Noise Cancel - either via Auto Noise Cancel function (Default), or manually. Auto is the recommended setting, and may take up to about one minute.

Most people immediately notice the weight difference between the 7000 (3.22kg) and the younger Minelab sibling GPX 6000 (2.1kg) - with the 7000 being about 50% heavier than the 6000.
The use of a quality Bunji/Bungee/Bungy cord can effectively reduce the "swing arm-carried" weight of a detector by at least one-half (50%) e.g. so that the GPZ 7000's "felt weight" is comparable to the full weight of the GPX 6000.

Recommended Techniques for Achieving Optimal Performance
Like other Minelab detectors, good ground balancing techniques are crucial to getting the optimal performance capabilities out of the detector. The initial ground balancing technique for the GPZ 7000 IS DIFFERENT to the technique you should use for a Minelab Pulse Induction (P.I.) detector like the GPX series of detectors. Minelab recommend the following ground balancing technique for the GPZ 7000:

“Ground Balancing   VERY IMPORTANT
The best way to ground balance initially after switch on with the Quick Trak trigger depressed, is to sweep the coil in a typical side to side search mode at the expected operating height above the soil surface, e.g. 2–3 cm or whatever the soil saturation or terrain will allow, but at the same time move forward at slightly faster than normal walking speed, so as to cover as much different ground as possible in the first 10 to 12 seconds. The idea during this initial period after turn on, is to expose the detector to as much different soil data as reasonably possible to improve the
initial calibration.
IMPORTANT!   DO NOT ground balance using a coil up and down motion (like one would do using a PI detector) initially after turn-on with the Quick Trak trigger depressed. This does not give the initial calibration enough different soil information to calibrate optimally. If ground balance is required again sometime later (but without turning the detector off), ONLY THEN is the usual (PI type of) ground balancing up and down coil motion OK.”

Minelab Software Updates
There have been two software updates released by Minelab for the GPZ 7000.
The first update (released in 2015) related to a new auto ground tracking algorithm, and improved auto ground balance function.
The second update (released in 2017) featured an all-new ‘Ground Smoothing’ function as a primary enhancement. This function provided selectable noise filters that help deal with difficult ground, especially salty soils. A ‘Semi-Auto’ setting was also added to the ‘Ground Balance Mode’ to provide improved ground balance stability.

Yellow Ferrite Ring Ground Balancing
Minelab also recommended the use of their Yellow Ferrite Ring for optimal ground balancing.
Minelab stated:
“It’s very important to Ground Balance the GPZ 7000 using the yellow ferrite at the start of your detecting session. By doing this, any ferrite-like components encountered in the soil will not cause any false signal audio responses. The updated software shows the use of the yellow ferrite as part of the animated guide sequence when you follow the Quick Start/Quick-Trak process. (This is also a way to determine if a GPZ 7000 detector has the new software installed.)”

Accessories included with the Minelab GPZ 7000 detector
Accessories included in the Minelab GPZ 7000 box (in addition to the detector + Minelab GPZ14 coil) are:
Quick-Detachable Control (Guide) Arm + WM12 Wireless Audio Module + KOSS headphones + Pro-Swing 45 Harness + battery charger & charging cables.

Optional Coils
The Australian company ‘Nugget Finder’ (NF) recently released the Minelab-approved ‘Z-Search’ range of non-spoked coils, namely a 17x13" elliptical coil, and also a 12" round coil. These coils have a DOD configuration, a 3year Warranty, and are rated as water resistant to 1metre. These NF coils also include a Minelab lower shaft.


Several incredible gold nuggets have been discovered in Australia over the past 8 years using the GPZ 7000, including down to depths of about 1 metre, and no doubt yet more big nuggets will continue to be unearthed.

Tips for Gold Hunting in Western Australia - Part 3

Tips for Gold Hunting in Western Australia - Part 3

TIPS  FOR  GOLD  HUNTING  IN  WESTERN  AUSTRALIA  –  Part 3

DETECTING TECHNIQUES
Gold Detecting Tips:
1.    Upon commencing detecting each day, consider doing a “Factory Preset” (on the GPX 6000) or “Reset Audio & Detection Settings” (on the GPZ 7000) – in order to optimise the operational performance of your highly-sensitive, Minelab pulse-induction detector.

2.    Be patient, the gold is not going anywhere – if the GPX 6000/GPZ 7000 becomes a bit noisy or “chattery”, then do a noise cancel followed by manual ground balancing using the “Quick Track” button. Some days I do this often throughout the day. This will optimise the performance of your GPX/GPZ so that you are not wasting time and possibly missing those quieter/faint target signal noises often associated with deeper gold.

3.    Swinging technique is also VERY CRITICAL to how much gold you are likely to detect. The “Low and Slow” rule is VERY IMPORTANT to find more gold. On soily ground (without too many sharp rocks) I would lightly and slowly rub my coil upon the ground, with overlapping sweeps from side to side, in order for the detectors pulse induction to energize gold nuggets as long as possible, and so as to increase the chance of the nugget being detected. I found that the coil skid plates lasted longer than I expected, and they are a small expense to pay for the benefit of finding more gold. (The gold price recently hit an-all-time record high of about AU$3,000 per ounce – nearly $100 per gram).

4.    After finding a gold nugget, and then re-checking the back-filled hole, I would always do a Noise Cancel, and a manual Ground Balance, to optimise the operation of my detector to find further nuggets.

5.    Whenever possible, and about half-way during a day of prospecting (during my midday lunch break), I would replace my detector's Lithium-ion battery with a fully charged battery.

6.    A Guide Arm (or Control Arm) attachment to the shaft of your detector can also be very useful. The end-grip of the guide arm is held by your non-detecting hand, so as to provide precisely controlled swinging of the coil within both the horizontal and vertical planes. The guide arm is also great for distributing some of the detector weight to the strength of your non-detector arm. I found that a guide arm greatly increased my prospecting comfort, especially on long, consecutive days of swinging.

7.    A Bungee cord (also often called a Bunji or Bungey cord) is often worn by many prospectors using the heavier GPZ 7000, especially if it is being swung for sessions of longer than a few hours. I also used a bungee cord on my GPX 6000 (attached from the shaft of my detector to the “D” ring on my harness) to minimise fatigue since I would mostly swing my 6000 for about 8 hours a day (equivalent to the running time of a fully charged battery). Some weeks I would swing for 7 consecutive days (that was about 56 hours of swinging a week). I found using a bungee made a huge difference to my muscle fatigue, and it provided me with greater swinging endurance time per day. More swinging = more ground coverage = more gold.

8.    If you find a gold patch, then use all the suitable coils you have on the patch, and also then thoroughly over the patch – that is, not only sweep-swinging on a grid-like pattern in both perpendicular directions, but also at angles across the patch. It never ceased to surprise me how much more gold I picked up with the GPX 6000 by detecting in many different directions on a patch. I would firstly exhaust the patch of gold using the GPX17” mono coil. When I was finding little more gold on a patch, I would then run the GPX11” mono coil over the patch and find more gold. Finally, I would then put the GPX14” DD coil and often find some more gold.


UNFILLED HOLES
One of my pet hates .... unfilled holes dug by lazy detectorists/prospectors - it ain’t rocket science.
Besides, it is generally much quicker to fill in a hole than dig it.
Who would like strangers coming into their yard and digging holes? let alone leaving them unfilled?
To me, leaving their holes unfilled is a reflection of, not only someone’s personality, but also their professionalism as a prospector.

During my several years of prospecting in W.A., I reckon I encountered tens-of-thousands of holes, some up to about 2-feet deep, left unfilled by other people using detectors. Most poachers do not backfill their holes - for various reasons.

I would often run my detector over many of these unfilled holes and find trash left in them, or in the adjacent spoil.

Fortunately, on about half a dozen occasions, I found small gold nuggets either still remaining in the hole, or in the spoil beside the hole - that were missed. On two occasions I found two nuggets within a hole after digging out the holes deeper.

Always re-check your holes & the spoil, and then check again after you have back-filled them. You might just get a nice surprise, like I did on a few occasions.


THEY NEVER GET ALL THE GOLD
One day I encountered two old "blow-in" (from interstate) prospectors near Kalgoorlie detecting some recent scrapes using a GPZ 7000 with a Minelab GPZ 19" 'Super-D' coil and a "modified" GPX 4500 with a Coiltek 18" Elite Mono coil.
 
I also had written permission to be on that lease to detect gold using my Minelab GPX 5000 with my new Nugget Finder 15" Evolution mono coil.
I got yarning to these blokes as they were packing up to leave. They loudly boasted that I "would be absolutely wasting my time" detecting the scrapes with my "stock 5000" as they "had completely flogged the ground" with both of their "high performance" detectors.

After they left, I fired up my trusty & proven workhorse GPX 5000, and I unleashed it upon that ground with enthusiasm. The first thing I did was walk upon the top of the many windrows (soil bunds created via machinery pushing/scraping operations), and I detected their tops, and both side batters.

Over the next few days, I pulled out over several ounces of gold (40+ nuggets) including a stunning half-ouncer at a depth of 1.5 feet. Most of the bigger nuggets were within the windrows. Other blokes who had recently pushed this ground with a loader not only failed to detect the nuggets in the windrows, but so too had these two "mature"-aged interstate prospectors missed all these nuggets. I had found more-than-enough "missed gold" to buy a brand spankin' new Minelab GPZ 7000. I had a few quiet chuckles to myself.

Over the next few years I was often amused hearing others claim they had "flogged" areas. This always presented a challenge to me - to try and prove them wrong. In the vast majority of cases I always found multiple nuggets from such so-called "flogged" ground.

It would seem to me that it was highly likely that all of those hundreds of nuggets I found on such so-called "flogged" grounds was due to poor detecting techniques used by others (including lack of patience and thoroughness).


TERRAIN/GEOLOGICAL INDICATORS
The vast majority (90%+) of gold nuggets I found in W.A. were detected with a distance of about 0.5km to 1km of a hill or hill/s. Many nuggets I detected were on the sides of hills or near the toes of hills too. A salt lake/s was often nearby too, within about 1 to 2 km's.

Most of the biggest nuggets I found in W.A. were at depth, often nearby large/old trees, and they were either within gold patches containing numerous nuggets, or nearby at least a few other smaller nuggets.

I also detected many nuggets buried under tree logs & branches that I carefully moved (watch out for snakes). Sometimes I would find unfilled holes scattered nearby/beside big logs that, surprisingly, had not been moved. I would then move these potential "nugget covers" and sometimes detect gold nuggets below. Many part-time/hobby detectorists are not absolutely thorough in their physical quest for gold. Full-time prospectors mostly think-outside-the-norm, and also take those extra, hard-yards steps to find more gold - probably because for many of them, their (and their family's) livelihood/s depends on it.

Saltbush vegetation was often nearby where I found gold too. I found several great nuggets beside the roots of saltbushes.

Often where I found gold (and other long-time local prospectors told me the same too) nearby was any/many of the following geological indicators:
Quartz + ironstone (often called “salt & pepper” ground)
Laterite ground
Banded Iron Formations (BIF's)
Greenstone belts
Jasper
Fault lines and contact zones (sometimes they can be naturally marked by way of obviously contrasting/sudden changes in vegetation types)

Many long-time, local prospectors in W.A. enjoy going out prospecting after heavy rains (when unsealed roads are not closed and not boggy) - since good gold is often eroded out of the ground and exposed, to be possibly spotted by a sharp-eye, or become within the range of detection of a detector coil.

 

REFERENCE BOOKS

There are many good books (and atlases) available for information on gold prospecting in Australia. I particularly like reference books that contain good maps, including locations of historical gold workings & mines. For decades in Australia, aussie prospector Doug Stone has authored several such prospecting books & atlases, including for Western Australia.


SIMPLE AIR-DEPTH CALIBRATION TEST:
At the start of every prospecting session, after turning my detector on and then doing the Noise Cancel, and Ground Balancing procedures, to get the detector running quiet & smooth, I would ALWAYS do an air-depth detection calibration test - to ensure my detector was running at near optimum performance for depth.
For this test I used a new/clean Aussie 5 cent coin (that I would always carry in my pocket), and I would confirm the maximum height (above the coin-on-the-ground) that the coil could just detect the coin.
Around Kalgoorlie, I generally obtained the following air-depth testing/calibration results (on an unburied 5 cent coin) for the respective Minelab detector & coil/s that I was using:

GPX6000 with 11" round Minelab Mono coil = 14" depth
GPZ 7000 with 14×13" Minelab Super-D coil = 16" to 18" depth
GPX 5000 with 19" round Nugget Finder Evolution Mono coil = 16" to 18"depth
GPX 5000 with 25" round Nugget Finder DD X-Search coil = about 20" depth

The above air-depths were the absolute maximum detection depths I generally achieved, and less than the detection depth of the same metal target buried in the ground, especially in highly mineralised ground.

Pulse-induction detectors will generally lose depth performance to some degree in highly to extremely mineralised ground, particularly when using highly-sensitive, flat-wound Monoloop coils, and especially as the ground surface temperature increases.
In "difficult ground" (highly mineralised and/or conductive), and sun-heated ground, a DD coil of at least the same diameter (albeit heavier than a Monoloop coil of the same diameter) may be more of an advantage.


PICKS
For extra grip for my big hands, and also for increased shock-absorbing capacity, I fitted a rubberised tennis handle wrap to my pick handle.

I always had a super-strong, round/flat, rare earth magnet mounted upon the top middle of the head of my pick. It was great for pulling out iron-based trash e.g. wire etc. It also often grabbed hot rocks. Don't just assume that all such hot rocks consist totally of iron and don't contain any gold. Over the years I found several hot rocks on my magnet that when broken up contained gold.


RECORD & SECURE YOUR NUGGETS .... & 4WD KEY
Most gold prospectors I have met (hundreds of them) use a plastic container (i.e. a used medication-type bottle) in the field to store their smaller, found gold, and most carry that container in either their shirt pocket or trouser pocket.

Over the years I was told by several local W.A. prospectors that they had found small plastic pill-type containers apparently dropped in the bush by other prospectors. Most contained gold nuggets. One bloke told me the container he found had 19 nuggets in it, totaling about an ounce. It was found on 'Pending' ground.

I store my freshly found nuggets within a plastic container, either secured:
(A) inside a zippered, deep compartment inside my backpack (together with the keys for my 4WD); or
(B) inside my trouser pocket - with a lanyard made from strong, pink coloured string that is securely connected from the bottle thread to a belt loop on my trousers.

I also use compact (pocket) digital scales to weigh, and I also photograph my significant gold nuggets in the field immediately after finding them.
That way if you then lose such a valuable nugget/s (either by accident, or it being stolen), at least you have a digital record (with a date & time stamp) of you having then had possession/ownership of it prior to it being lost or stolen.


LOOKING AFTER THE BUSINESS END OF YOUR DETECTOR
I regularly inspect my detector coils for any damage, and very carefully/gently remove the coil skid plate to clean out any dust and soil that may possibly congregate over time. In Western Australia where highly to extremely mineralised soils are common, such very fine mineralised dust can eventually find it’s way into between the coil and the skid plate.

This is even more likely to occur for large diameter spoked coils, compared to small round solid coils – mainly due to the significantly more total length of the contact faces between the coil and the skid plate.
If enough such material gets in, and also moves around whilst swinging, then this can affect the performance of highly sensitive, pulse-induction detectors.

I also wrap the circumference of all my coils with a quality adhesive tape. This acts as both a seal against any possible ingress of moisture and/or dust, and also as a protective layer on the outer vertical edge of the coil which nudges/rubs on soil, rocks, etc. I prefer Scotch heavy-duty grade ‘SUPER 88’ vinyl tape. It usually lasts me several months of swinging.

Talking about dust - which can find its way into almost all small gaps - it can pay to make sure that all the pin connections for all cables (like the coil cable plug, and also any battery cable plugs) are fully inserted, with the screw rings also done up firm.

Given the tens-of-thousands of dollars I spent buying pulse-induction metal detectors over the years, I always protected these investments from the dust, heat, and potential damage (e.g. caused by impact/scratching etc), by way of fitting quality, Aussie-made, padded canvas protective covers over the control box of each detector. Such protective covers can also protect the manufacturer’s labels of serial number/security codes – which may be useful down the track.
Furthermore, for concealment and ease of transportation of my detectors and accessories, I also use quality, Aussie-made, padded canvas carry bags for all my detectors.

When I was gold prospecting full-time in W.A. I soon learned the benefit of dusting down my detector & coil/s at the end of each day (with a soft cotton rag), prior to placing my detector & coil/s into the padded carry bag. This end-of-day ritual sure helped minimise the amount of fine dust that got caught inside the canvas carry bag. After every week of prospecting I would empty my carry bag of it's contents, and then turn it inside out to thoroughly shake out any dust that had congregated. I also kept all electrical-related accessories (like spare cables, and batteries and headphones, etc), within separate plastic clip-seal bags to minimise any dust entering the plugs or connections. This held me in good stead for years without any issues.

 

[Nugget image source - Facebook page of Finders Keepers Gold Prospecting - Kalgoorlie, W.A.]

Tips for Gold Hunting in Western Australia - Part 2

Tips for Gold Hunting in Western Australia - Part 2

TIPS  FOR  GOLD  HUNTING  IN  WESTERN  AUSTRALIA  –  Part 2 of 3

To prospect safely alone in W.A., particularly when I was solo free ranging (i.e. patch hunting on my own) and some days walking up to 8km away from my 4WD, I always carried a fair bit of gear on my body, for both practical & safety reasons.

Accordingly, I used a very comfortable load bearing, mesh-style vest (featuring a rear backpack and many pouches). It typically hit the scales at about 12kg (much heavier than my Minelab pulse-induction detectors + big pick). I would always carry at least 5 litres of water, 3 days of food rations,  first-aid kitLED headlamp,  LED torch including strobe light, a PLB,  an extra GPS device (apart from the Trilobite App on my phone), spare batteries, Gorilla tape, cable ties, cigarette lighter, a LifeStraw water filter, Leatherman tool, etc.

Another option for carrying less gear (including detecting closer to your vehicle) is to use a  harness.

It pays to carry more-than-sufficient water – both on foot, and in your vehicle. Many people who perished in remote areas in recent years did so away from their vehicles and also without water. (e.g. many people forget, or simply do not consider, that the windscreen washer water reservoir within the engine bay of most 4WD vehicles can contain at least a few litres of pure water – that can possibly be drinkable, as an absolute last resort in the event of an emergency. I do not add any chemicals to my water reservoir, and regularly flush & refill it with clean and pure water, for that very reason. Who knows …. Something so simple could save a life one day).

If you are intending to prospect alone in remote areas, it is also important to consider issues like:
Reliability and maintenance of your vehicle
Carrying suitable & sufficient water, food, safety equipment, fuel, and spare parts, and allowing for potentially being stranded for many days
Communications equipment
Weather forecasts
Spare metal detector/s and batteries and cables and coils
Spare key for vehicle – not locked inside the vehicle
Charging of batteries (e.g. via deep-cycle battery and/or solar or generator)


DOUBLE-RECORD THE LOCATIONS OF YOUR VEHICLE & CAMP
In recent years, several prospectors (mostly older blokes) have gone missing in W.A. Despite extensive searches, some missing prospectors have not been found, nor any of their prospecting gear. This makes you wonder – fools play? or foul play?

One valuable lesson I learned was to double-record the co-ordinates of the locations of my parked 4WD and camp. I would record the GPS co-ordinates on both my Trilobite App, and on my back-up Garmin GPS device (just in case one of them ever failed). This method served me well, especially in terrain which was new to me, or where the vegetation was all the same, and in the absence of nearby landmarks.

 
PERSONAL LOCATOR BEACONS (PLB’s) / EPIRB’s
Did you know?
That  some PLB/EPIRB devices have been activated unintentionally  by being too close to the coil of a pulse-induction metal detector that is turned on/operating.

In 2017 a prospector in the Pilbara, Western Australia - who reportedly had possession of a Personal Locator Beacon (PLB) - unknowingly had his 'KTI' brand SA2G model PLB activated - when it came within very close proximity of the operating coil of his pulse-induction metal detector.
(Also reported on the Facebook page of "Finders Keepers Gold Prospecting" – refer to posts on 5 October 2020).

I understand that due to this issue - KTI re-designed their SA2G model PLB - which is now designated as the SA2GN model.

There have also been other similar accidental activations of EPIRB/PLB's by operating pulse-induction metal detectors being placed too close.

There are in excess of fifty (50)  different models of EPIRB's/PLB's available on the Australian market. 'KTI' is one of the most popular brands of PLB.

To avoid the potential for accidental activation of my PLB – I keep my PLB (inside the rear of my backpack) and stored inside a waterproof, stainless-steel canister – which acts as a ‘Faraday Shield’ – to block electromagnetic fields/radiation.

 
PLB/EPIRB TESTING + AMSA RECORD
Given that most of my prospecting was alone in W.A, and often in remote areas, I ALWAYS carried a PLB/EPIRB.
Not only that, I also REGULARLY tested (before every trip away or every 2 months - whichever came sooner) that my PLB was in proper working order. This included testing that the battery life was OK, and also that the transmitter function of the device also worked correctly - via the Manufacturer's recommended Test Mode functions on the device.

After this was done, I would also  update my AMSA Registration record  (via my online account), including information about my planned pending trip, re: my vehicle/s, planned trip route, likely camping locations & estimated travel dates.

HARD GROUND = HARD WORK BY HAND
Some of the hardest ground I have encountered during prospecting is in W.A. I soon learned the importance of using  a high-quality, heavy-duty pick. In some locations I found gold within/near Calcrete (a natural, concrete-like formation). Gold is often associated with the presence of Calcrete, and also with the presence of ironstone and quartz (particularly "rotten" quartz). In some instances where I detected gold contained within Calcrete, I used a cold-chisel & steel mallet, or a heavy-duty crowbar & sledgehammer (stored within my 4WD) to free the gold nuggets from calcrete.

Quality gloves are also useful to prevent blisters, abrasions, cuts, sunburn and hot ground.

On some hot summer days, the ironstone-pebble strewn ground got so hot that I was unable to hold by bare hands upon the ground for longer than about 3 seconds before burning my palms. Knee pads (including incorporated into work trousers) can also be very useful – some days I would dig & backfill over a hundred holes – which really worked my knees & back.

POTENTIAL THREATS
After spending years living, working and prospecting in the bush throughout Australia – not too much worries me out there in the bush.

I have had many solo encounters with lone wild dogs, and they all appeared to be very cautious of my presence. During the several encounters I have had with a pack of wild dogs, I was more concerned as they seemed less scared of me and more prone to come closer to me as a pack, before I scared them off.

My advice – Be aware of your surroundings (“situational awareness”), particularly if you are alone. Accordingly, I prefer to mostly use  speakers  when detecting, or sometimes a sports earphone in one ear (not earmuffs-style headphones). Noise is a generally good deterrent against wild animals, including wild dogs. Interestingly, I read that scientists from two Queensland universities recently found that some  Australian snakes such as Taipans, brown snakes and death adders can hear, as well as sense vibrations.

JOE BLAKES & SPINIFEX
Leg gaiters – for protection against both “Joe Blakes” (snakes), and also Spinifex needles (common throughout Western Australia’s goldfields). Over the past 7 years I have been wearing gaiters (‘SNAKEprotex’) – that were rated for protection against venomous Australian snakes (including an adult Taipan which can possess fangs up to one-half-an-inch long). I found gaiters excellent for protection against spinifex needles when I was gold prospecting in both central Australia and Western Australia. Lots of good gold country in W.A. often contains plenty of spinifex.

PROSPECTING AT NIGHT
Unless you have significant local prospecting experience, you would be taking big risks to prospect alone in W.A. at night in terrain you are not very familiar with. Many biting/stinging creep-crawlies come out at night. It is also much more challenging to judge the distance of range at night.

I only ever prospected alone at night upon pushed/scraped gold patches (well-defined areas) nearby where my vehicle was parked, with an LED strobe light operating upon the roof-rack (as a great reference point marker). A spare headlamp + spare batteries are a MUST.

 

PERFORMANCE ENHANCING
Be mindful of your personal performance when prospecting alone. A few things that I found affected my prospecting performance were not keeping properly hydrated, lack of regular meals & breaks, poor boot comfort, and poor ergonomics of backpack & detector.

Also be mindful of issues that may affect the performance of/interfere with your super-sensitive, pulse-induction metal detector e.g. mobile phones NOT set on Flight Mode, or wearing steel-capped boots, or UHF radios, or  pin-pointers,  or the digging pick head too close to your big coil,

 
FLIES & HEAD-WEAR
During my most recent prospecting travels over the past 7 years throughout most of our awesome continent of Australia, I had not encountered such numbers of menacing flies as I found several hundred kilometres north of Kalgoorlie. From sunrise to sunset, during my regular 8-hour-days of swinging a gold-hunting “beepstick”, the small, fast flies were absolutely relentless.

Annoyance-reduction measures that helped me somewhat included either wearing a head-net (which I generally do not like), or mostly wearing a broad-brimmed, shady hat with a Scrim mesh material curtain draped around the sides & rear (to also provide sun protection), and wrap sunglasses with large lenses. To some degree, I also found that dabbing a suitable repellent (I preferred to use a non-DEET/natural oils-based solution such as Nature’s Botanical Rosemary & Cedarwood Oils Repellent) on my face and the Scrim mesh also deterred many flies. Beware that DEET-based repellents can damage plastics - including the screens of detectors, particularly if the screens do not have  a protective cover.

Unfortunately, some of the best gold country I encountered in W.A. also had the worst masses of flies.

 

HOT ROCKS & METEORITES
During more than 300 days of prospecting in W.A. I reckon I detected hundreds of hot rocks. Moreso with my Minelab SDC2300 than with my GPX 5000 and GPX 6000, and GPZ 7000. Having a curious mind, I always pocketed these highly mineralised/often heavy/often magnetic rocks to take home and smash up in a dolly pot. Occasionally a small bit of gold was won from such hot rocks.

Sometimes such “hot rocks” are in fact of extra-terrestrial origin e.g. meteorites, some of which contain iron, nickel and cobalt. Not all meteorites are attracted to a magnet. Iron-Nickel meteorites (with a majority content of iron, and up to about 8% nickel content) will very strongly attach to a magnet, and hence be clearly detected by a metal detector. Several different types of  meteorites have been found in the goldfields of Western Australia, including near Kalgoorlie. Some of the rarest types of meteorites are worth more than gold per ounce.

 

TRASH

Many prospectors I met have a strong magnet attached to the outer top of their pick head. In trashy areas, a good magnet can pull out a lot of ferrous junk metals (including tiny bits of wire that can cause a lot of wasted time to find otherwise)

I heard similar stories from other prospectors, and I experienced it myself – the detection of aluminium beer/soft-drink cans down deep inside goanna holes, and concealed inside nearby logs. Talk about a frustrating waste of time. So beware of animal tunnel entrance holes, or hollow logs, nearby where you detect a target.


BIG NUGGETS RECENTLY FOUND IN W.A.
In recent years many impressive gold nuggets (and gold/quartz and gold-ironstone specimens) have been unearthed using  Minelab pulse-induction-technology metal detectors in Western Australia, including near Kalgoorlie.

(Images source - Facebook page of Finders Keepers Gold Prospecting - Kalgoorlie, W.A.)

 

OTHER THAN GOLD
Some other interesting things found by prospectors in W.A. include:
Fulgurite (I found a 3.9kg specimen), Opal – including Moss Opal, Chrysoprase (“Australian Jade”), Devils Dice, Meteorites, Australites (Tektites), stone tools, black octahedral Hematite crystals, metallic fragments of SkyLab, gold sovereign/half-sovereign coins, etc.

Other useful tips will be discussed soon in Part 3 of this article – to be published online soon.