Gold Rat Metal Detectors is located 6/50 Freda Street Upper Mount Gravatt. This is the only store to stock Metal Detectors. Gold Rat Engineering is located 4/16 Redcliffe Gardens Drive Clontarf This is where you will see the largest range of your highbankers, sluices and accessories

News — Coiltek

Blog Menu

Some Awesome Aussie GPX 6000 Finds

Some Awesome Aussie GPX 6000 Finds

* Some Awesome Aussie GPX 6000 Finds *

The Minelab GPX 6000 Pulse-Induction detector has now been available in Australia for about 3 years. In that time some awesome nuggets have been unearthed throughout Australia. Some of these significant finds have been publicised, and not surprisingly, many fantastic finds have not been publicised for various reasons.

Several big chunks of gold have been recently found in Western Australia.

 

Below are some of the Minelab GPX 6000 finds that have been shared online:

The big nugget shown in the two photos above reportedly weighs  about 13 Ounces  (about 0.4 kg).  My "guesstimation" is that the total weight of all of the above nuggets would be  at least 30 Ounces !

 

 

The nugget shown in the above two photos was detected using the GPX11" coil at a depth of about 1.5 feet.

 

Below are some more finds using the GPX 6000:

“Here are two of the nicest bits for the season, biggest is 5.5 oz (171.2g) and the other is just over an ounce (35.5g). Both found with a 6000 while pushing. Interestingly the big bit was laying flat, in a crevice in a rock bar, about 60 cm down I suppose (from the bottom of the push) but it was not an inverted signal, and I have no idea why.

Every other solid bit I've got from a gram or so up has been an inverted signal. It started off as a normal up down signal, sounded very OK like a few gram specie 10 inches or so down, good but not outstanding. It just got louder and louder the deeper I got. By about 40-50 cm down I knew it was going to be a better bit, maybe an ounce or two even, and I was convinced that it had to be a specie as the signal wasn't inverted.

The pinpointer was going crazy over a red rock stuck in the crack and I couldn't see any gold yet so I was convinced it was under the rock, got the biggest shock when I got that rock out and felt the weight. It was flat and heavy and clearly a nugget but even after giving it a wash I still couldn't see any gold.

Took a couple of days in alibright for the red coating to dissolve. It has about 6 g of rock in it based on an SG test so it's technically a specie but I'm happy to call it a nugget. The smaller bit was in a different spot, in old wash, probably 70 cm or so down from the surface. I had pushed it though so I only had to dig a few inches. Before I dug it I tried detecting it from the surface level and got no response. Had to be down another 6 inches or so before any signal but it was inverted all the way. The bit was in a small crack but standing upright on it's side and it looked bright and shiny like it does now when it was still stuck in the hole.”

 

 

 

An old Aussie gold prospector (who has used all of Minelab’s other pulse-induction detectors over the past decade (e.g. SDC 2300, GPX 5000 & GPZ 7000) has also used the GPX 6000 in Western Australia for 118 days (about 1,000hrs of swinging) and on 100 of those days, his GPX 6000 detected 854 gold nuggets in highly mineralised ground. He mostly used the large Minelab GPX17x13” elliptical Mono coil for excellent ground coverage (“patch hunting”) and depth capability. In fact, the GPX17 coil easily detected two spherical-shaped nuggets (a 5-grammer, and a 6 grammer) at depths of between 40cm and 45cm in highly mineralised ground north of Kalgoorlie. The GPX17 coil also picks up the small bits too – using the proven “Low & Slow” technique. He also found the GPX14 DD coil excellent for use in salty/conductive ground (where it was almost impossible to run a Mono coil), as well as in areas within/nearby high electromagnetic interference (EMI).

 

 

Liz Pickthall spends her spare time detecting in the central goldfields of Victoria.

"I finally had seen and heard enough, and at the age of 28 I decided to go out and invest in my first detector. Only then did I realise my true love for it, and I’ve been addicted ever since. As the years went by and my love for detecting grew, I started to work less and detect more.

After upgrading my metal detector to the GPX 6000, I was keen to upgrade my coil as well. I waited for the release of all brands of coils, and was lucky enough to be able to try before I bought two different coils – one of which was the Coiltek 9” GOLDHAWK.

It didn’t take me long to see that it was the standout performer in all areas including weight and sensitivity – and it worked wonders on all ground types in the Victorian goldfields. I was so impressed by how quiet it ran for such a sensitive coil. The 9” coil has found gold in the most ‘flogged out’ areas, with the coil’s size making it so easy to get in tight areas under and around bushes and trees.”

 

 

 

 

  

 

  

 

 

 

 

 

Imagine how many tens-of-thousands of gold nuggets (& specimens) have been found throughout Australia over only the past 3 years using the mighty Minelab GPX 6000 detector.

Imagine how many more huge chunks of gold are still out there throughout Australia - that have never had a GPX 6000 scan over them !

To boot ..... there are now  SEVEN  (7)  different coils available for the GPX 6000.  Even better - four of these new coils are AUSSIE-MADE.

Coupled with a super-low 1.225 kHz operating frequency of the GPX 6000 - it's no wonder the GPX 6000 is a gold magnet !     (By comparison the GPX 5000 "is configured to operate at a fundamental operating frequency of 5 kHz", and the GPZ 7000 "is configured to operate at a fundamental operating frequency of 3.675 kHz”, whereas for the SDC 2300 "the transmit frequency is about 3 kHz")

With the gold price at an all-time-ever record high (of over AU$3,700 per Ounce in late April 2024) - you only need to find about 2.5 ounces of gold to cover your investment cost of a new GPX 6000.

 

Have I Found a Meteorite ?

Have I Found a Meteorite ?

Have I Found a Meteorite ?

Below are some links to websites containing informative guides on how to identify a meteorite:

 

The Differences between a Meteorite, and an Impactite, and a Tektite
In the simplest terms –

A Meteorite is a piece of rock or metal that has fallen to the earth's surface from outer space as a meteor. Not all meteorites consist of metals. Most meteorites (about 95%) that have been recovered on Earth are of the ‘Stony’ type.

Meteorites of high density are heavier, and strongly attracted to a magnet due to the amount of Iron and Nickel they contain. Most of the largest meteorites ever recovered on the mainland of Australia are of the Iron-Nickel Type. These are one of the least common types of meteorites found (only about 4% are of the Iron-nickel type). In fact, the largest recorded meteorite found in Australia was officially discovered in 1966 and it weighed over 12-Tonnes.

 

A Tektite is a terrestrial molten rock fragment ejected out of the crater during a meteor impacts.

Tektites are small, black blobs that might pass for hardened bits of asphalt but they are actually glassy stones. They commonly take on distinctive regular shapes like teardrops, jelly-beans, dumbbells, and interesting flanged buttons that look like the tops of large rivets with the stems melted off. Tektites are found strewn about on the ground in widely separated "fields" around the world, the largest of which covers most of Australia. Many prospectors find tektites throughout Central Australia and the south part of Western Australia.


An Impactite is a terrestrial rock modified by the high stresses of pressure and temperature during a meteorite impact. It is generally the rocks present in the impact crater. It can also include brecciated rock materials, and shatter cones.


XRF Testing of Metallic Specimens
Some jewellers, and gold/jewellery buyers, use a portable/handheld X-Ray Fluorescence analyser (commonly called an “XRF gun”) to non-destructively test items - in order to determine their metallic composition. XRF guns can cost in the order of tens-of-thousands of dollars to buy.

Accordingly, suspected metallic meteorites can be tested by an XRF gun to quantify the percentages of metals present.
If you have a piece of metal that does attract a magnet, and you want to know if it is an iron-nickel meteorite - then you could try and obtain an XRF analysis for the elements of: Iron (Fe), Nickel (Ni), Cobalt (Co), Chromium (Cr), and Manganese (Mn).

Iron-nickel meteorites will typically contain about: 75 to 95% Fe, 5 to 25% Ni, 0.2 to 2% Co, and less than 0.05 % each of Cr and Mn. The nickel/cobalt ratio in meteoritic metal is usually in the 10 to 25 range. If the metal contains more than 0.05% Chromium or Manganese - then it is NOT a meteorite.

Recently, a customer visited our store to seek advice about some interesting metallic specimens he had detected in Queensland. The customer suspected they may have been iron-nickel meteorites. I was informed that the specimens were very heavy, and very-strongly attracted to a magnet. I was advised that subsequent XRF analysis results indicated the following composition: Fe 97.65%, Mn 1.2%, Ni 0.68% and Cr 0.56%. Based on the absence of Cobalt, and also the Manganese & Chromium contents both significantly exceeding 0.05% - these XRF results indicated that the subject tested specimen is NOT an iron-nickel meteorite.


What is a Widmanstätten pattern ?
The Widmanstätten pattern (also known as Thomson structures) is a distinctive formation of interweaving (cross-hatched) lines that appear in some Iron-Nickel meteorites when a cut & polished cross-section of such a metallic meteorite is etched with weak acid.

The methods used to reveal the Widmanstätten pattern in iron meteorites vary. Most commonly, the meteorite is firstly faceted or cut/sliced, then an exposed face is ground and polished, then cleaned, and etched with an acidic etchant (e.g. a mixture of 1-part Hydrochloric Acid, added to 2-parts Hydrogen Peroxide in a non-metallic container). Then the prepared specimen is washed, and dried.


Can I keep a meteorite I found in Australia ?
That depends on WHEN ?  HOW ?  and WHERE ? you found a meteorite in Australia.
Most of the States (and Territories) in Australia have laws (since from about the 1970’s/1980’s) which deem any meteorites found in those particular States to be the property of the Crown or State.

However, those laws do not apply to other specimens like Tektites (Australites) and Impactites – that are also often formed when a meteorite impacts the ground. Sometimes Tektites and Impactites are also found near an impact crater.

Queensland’s Fossicking laws prohibit the collection of meteorites in Queensland whilst fossicking.

However, it is my understanding that if a person was in Queensland or New South Wales, AND was lawfully permitted to be upon such land AND also permitted to remove any specimens found on such land, AND if by way of chance discovery (e.g. NOT fossicking in Queensland) found a suspected/unconfirmed specimen – then they would be able to take possession of such a specimen.

Can I lawfully sell a meteorite I found/acquired in Australia ?
If you lawfully found a meteorite in Australia, or lawfully acquired a meteorite within Australia – then you are lawfully permitted to sell the subject meteorite within Australia.

In 2021, an ABC News report was published online stating that in 2016 two men, who were reportedly fossicking for gold on Western Creek Station, near Georgetown in North Queensland, detected (using a Minelab pulse-induction metal detector) a meteorite weighing 24.3 kilograms. It was also reported that they sold this Iron-nickel meteorite to ‘Geoscience Australia’ for AU$200,000 (i.e. over AU$8 per gram).

Similarly, to the above 24.3kg meteorite being detected on Western Creek Station – in April 2016 I was informed by an Australian prospector that in early 2016 he was gold prospecting using a Minelab GPX 5000 detector on the eastern part of Western Creek Station (near Georgetown) where he detected a 9.6kg metallic specimen (a suspected Iron-Nickel meteorite) at a depth of about 0.4 metres.

The sale of a meteorite in Australia to an overseas buyer is prohibited without an official export permit pursuant to Commonwealth laws.

Recent Unusual Meteor Sighting in Australia
In May 2023 it was reported that a fireball lit up the sky in Queensland between Mackay and the Gulf of Carpentaria. NASA confirmed that this meteor was the LARGEST recorded over Australia in at least 30 years.

When it exploded, the meteor had an altitude of about 30 kilometres above Blackbull, a small rural locality between the Gulf communities of Normanton and Croydon, in north-west Queensland.

The data also revealed the meteor was travelling at a velocity of almost 30 kilometres per second. Scientists estimated that the meteor had a diameter of about 3.5 metres (of equivalent size to an average caravan) and weighed about 80 tonnes.

My further enquiries with NASA obtained additional data indicating that when the meteor was detected travelling from an altitude of 100km, down to 30km altitude, it was heading approximately Westwards (with an approximate bearing of 280 degrees), whilst falling at an angle of about 40 degrees.

Due to the blue and green colours of the meteor fireball observed, it is suspected by scientists that this meteorite was a metallic (Iron-nickel) meteorite.

Will fragments of this meteorite be found in Queensland ? - including perhaps by someone using a metal detector ?


NASA data also indicates that in recent years (since 2014), there have been several significant fireball events detected in North Queensland.



Where in Australia have meteorites been found ?
The following free on-line search database contains over 700 records of various types/sizes (and photos of) meteorites that were found in Australia over the past few centuries: 

https://encyclopedia-of-meteorites.com/Meteorites

In recent years a few large meteorites have been detected on Western Creek Station in North Queensland by gold prospectors using Minelab detectors featuring pulse-induction technology.


Suitable Detectors & Coils for Meteorite Hunting
Meteorites containing sufficient quantities of iron/nickel (including the 'Stony-Irons' Meteorite Types) are detectable with a metal detector. Since metallic meteorite fragments are sometimes strewn about an impact crater, often for many kilometres away from the crater, then a suitable metal detector is a lightweight detector with a large coil – which is ideal for quicker ground coverage, and also greater depth capability.

Many meteorite hunters use a lightweight, Very Low Frequency (VLF) technology detector fitted with a 15-inch DD coil.

Recently released Minelab VLF detectors – which can operate using a variety of DD coils ranging in size from 6 inch diameter up to 15 inch diameter - include the X-TERRA PRO ($499), and Equinox 700 ($1,079), and Equinox 900 ($1,499).

Both Minelab, and Coiltek, manufacture a 15-inch diameter coil for these VLF detectors – priced at about $400 to $450.

 

 

Furthermore, in about early December 2023, Coiltek released a new BIGGER coil - the  Coiltek 18" NOX coil  ($470). It is a DD configuration coil of 18-inches (45cm) diameter - that is also compatible with the Minelab Equinox range of detectors, and also the Minelab X-TERRA PRO detector. This coil weighs nearly 1kg, is rated as waterproof to a depth of up to 5 metres, and carries a Coiltek Warranty for 2 years.

 

You don’t necessarily need a more expensive & heavier Pulse Induction (P.I.) technology metal detector to detect metallic meteorites. Other than a VLF detector, some meteorite hunters also use a lightweight, telescopic walking stick – fitted with a strong, rare-earth magnet attached near the end closest to the ground.

Tektites (which are of a glassy composition) are not detectable by a metal detector. Most are found by sight – often discovered washed down to low points (“sumps”) in the terrain (e.g. gullies or clay pans or salt lakes).


Many prospectors detect so-called “Hot Rocks” throughout Australia. Often many prospectors will simply discard such metallic specimens without further examination of them.

Mostly, such “Hot Rocks” are of terrestrial origin, and sometimes they can contain minerals such as gold. I have detected several hot rocks in W.A., and upon breaking them, I found they contained gold either in the form of a nugget, or a specimen, or concentrated gold mineralisation.

If such hot rocks are very heavy (e.g. like the weight of iron steel), and also highly magnetic, and also have smooth indentations (called “regmaglypts”) on the outer surface - then perhaps the specimen may be more than just a highly-mineralised, terrestrial hot rock ? ….. possibly a meteorite ?

Meteorites containing Gold ? ?
Over the decades, I have heard many explanations/theories (including from experienced geologists and prospectors) on how gold was formed on planet Earth. Most theories relate to terrestrial formation processes. In recent years, some scientists believe that gold was deposited upon earth by meteorites. A study published in 2011 suggested that:

"A massive meteor bombardment 3.9 billion years ago provided most of the gold and other precious metals found near the Earth's surface today"

Interestingly, a United States Geological Survey report published in 1968 stated that:

"The reported gold contents of meteorites range from 0.0003 to 8.74 parts per million. Gold is siderophilic, and the greatest amounts in meteorites are in the iron phases. Estimates of the gold content of the earth's crust are in the range of 0.001 to 0.006 parts per million."

 

 

 

Aussie-made Coiltek GOLDHAWK coils

Aussie-made Coiltek GOLDHAWK coils

Aussie-made  Coiltek  GOLDHAWK  coils

The Minelab GPX 6000 detector has now been available for nearly 2 years. Many prospectors throughout Australia have re-visited goldfields, including their “fav” patches, that they considered “flogged” and then unleashed the GPX 6000 over such areas to find even more gold, including at depth.

The popularity of the GPX 6000 is not only due to its high performance, but also because it is of relatively light weight (50% lighter than the Minelab GPZ 7000), and it is very easy to use - even for “newbie” detectorists, and budding “prospectors”. It also costs approximately 20% less (a few thousand dollars less) than the Minelab GPZ 7000.

Now, there are even more coil options available for the GPX 6000 detector. In fact, there are currently more coil options available for the GPX 6000 than for the GPZ 7000.

With Minelab’s approval, long-time Aussie coil-maker ‘COILTEK’ recently released a range of 3 different sized Monoloop (“Mono”) coils for the GPX 6000. These are named the ‘Goldhawk’ series of coils.

The Coiltek Goldhawk coils (very pale tan coloured) are rated as waterproof to 1-metre depth, have a 2-Year Warranty, and include the following sizes/weights:

9 inches round - cost $609  (weighs 700 grams)
10x5 inches - cost $579  (weighs 575 grams)
14x9 inches – cost $639  (weighs 900 grams)

Feedback so far, including from many gold hunters throughout Australia, has been impressive as to how stable (smooth & quiet) the coils run, and how sensitive they are to all sizes of gold nuggets, with great depth capabilities.

Many people also prefer the elliptical shaped coils, for not only ease of use in confined areas/less-open ground/more vegetated ground, but also for better pinpointing capability than a round coil.

 

 

 

New Coils for the GPX 6000

New Coils for the GPX 6000

New Coils for the GPX 6000

The Minelab GPX 6000 detector kit ($7,999) includes the Minelab 11” round Monoloop coil (GPX11 coil) and also the Minelab 14” round DD coil (GPX14 coil). The GPX11 coil weighs about 600 grams, and the GPX14 coil weighs about 900 grams.

An optional extra coil is the larger, elliptical Minelab 17”x13” (GPX17) Monoloop coil (cost $579) that weighs about 800 grams.
New Minelab skid/scuff plate covers for the three Minelab coils range from about $33 up to $45.

Aftermarket coil makers – both Nugget Finder, and Coiltek, recently released a range of various-sized, non-spoked/solid, Monoloop coils for the GPX 6000. Nugget Finder have released the ‘Xceed’ series of coils, and Coiltek have the ‘Goldhawk’ series of coils. These coils are all approved by Minelab.

The Nugget Finder Xceed coils (white coloured) have an ABS housing, are rated as waterproof to 1 metre depth, have a 2-Years Warranty, and include the following elliptical sizes:

8x6 inches - cost $659 (weighs 570 grams)
12x7 inches - cost $699 (weighs 700 grams)
16x10 inches – cost $745 (weighs 970 grams)

The Coiltek Goldhawk coils (very pale tan coloured) are also rated as waterproof to 1 metre depth, also have a 2-Years Warranty, and include the following sizes:
9 inches round - cost $579 (weighs 700 grams)
10x5 inches - cost $579 (weighs 575 grams)
14x9 inches – cost $639 (weighs 900 grams)

Feedback so far from a many gold hunters throughout Australia has been impressive as to how stable (smooth & quiet) the coils run, and how sensitive they are to all sizes of gold nuggets, with great depth capabilities. Many people also prefer the elliptical shaped coils for not only ease of use on less-open ground/more vegetated ground, but also for better pinpointing capability than a round coil.

Maintenance Tip:
To minimise scuff marks/soil staining on the topside of coils, a protective adhesive skin or suitable adhesive tape can be applied. I used UV-resistant Gorilla tape on my Minelab coils – which I found fit-for-purpose.